Safety Relief ValvesSafety valves for solar energy systems Series SVE-SOL
The membrane safety valve is part of the safety device for solar energy systems installations feed with water or water mixture as vector, according to DIN 4757part 1. The valve discharge pressure is factory-set and cannot be modified without manumission of the seal, placed on the cap, which indicates setting pressure and approval mark. Series SVE SOL
|Thermal drain valves Series VTFN|
Positive action thermal drain valve, with manual resetting and optical signal.
Protection class : IP40. Set temperature : 95°C. Drain capacity without filling :
VTF 1.1/4" - 176.775 kcal/h equal to 7070 l/h
VTF 1.1/2" - 318.200 kcal/h equal to 12728 l/h.
ISPESL approved. According to EEC 89/336, EEC 73/23, PED 97/23/CE. Identification number CE1115 Series VTFN
Automatic Control ValvesAutomatic control valves serie EU100
The valves consist of a two-way main valve body and a hydraulic control circuit. The
valve is actuated by the same hydraulic energy as the fluid, with consequent guarantee of independence and reliability of the equipment. The various solutions proposed for the pilot system mean that the valve can be used for performing widely differing functions and applications.
MODELS, cast iron construction:
DN 50-600 (PN 10-16)
Versions with needle valves (standard)
Versions with control unit EU900 (basic valve EU100 + UR) Automatic control valves serie EU100
Shut-Off ValvesAir vent valves with float Series MVD - MV - MKV - MKL - 2161C - MXV
Are automatic and/or manual devices for discharging air from heating and
These devices are used in all traditional heating systems (independent, central, radiant panel, etc) for discharging air during the filling phase and the air released into the water during the heating phase, which obstructs the normal circulation of the heat carrier fluid above all at the points where it circulates at a low speed (heat emitters), thus reducing their thermal efficiency. The air vent valves allow the air to be discharged at the points of the system where it accumulates (distribution manifolds, tops of the risers or directly in the boiler). Air vent valves with float Series MVD - MV - MKV - MKL - 2161C - MXV
|Bronze valve 3-way Series 296|
The Valves Series 296 are 3-way devices for shutting off boilers and expansion vessels in closed-circuit systems. They are made of bronze for the threaded versions and cast iron for the flanged versions, with ports according to I.S.P.E.S.L. standards. Series 296
Gas ProductsLPG and Natural gas leak detectors Series GSX - GSW
The new range of gas leak detectors under the name of “Gas Sentinel” for methane and LPG, available for wall and flush mounting, comes with a new design and more compact size as well as with performance characteristics, in terms of reliability and sensitivity in measurement, in accordance with current European standards (EN50194). The alarm and closing of the solenoid valve are activated by the first or second threshold depending on the programming of gas leak detector, selectable by user.
• Provision for simultaneous monitoring, through serial communication link, up to 11 zones: (1 main detector + 10 secondary detectors)
• Provision for connecting the network of gas leak detectors to a PC for monitoring or programming the detectors using a special software kit.
• Malfunction: the gas leak detector is provided with circuit for self-diagnostics, which, in the event of critical fault of the sensor or to one of the main components, trips giving a visual signal (yellow LED). Series GSX - GSW
Electronic ControlsChronothermostat Series MILUX-RF
The MILUX-RF chronothermostat is able to control and regulate directly the central heating (electric, Gas, Oil) or cooling system as well as electrical panel heating. It is a seven day program/hour which enables power savings in harmony with your every day life. Each trasmitter has a different code in order to avoid interferences problems with the neighbourhood. Series MILUX-RF
Installation Protection ProductsWater hammer arrestors Series APW, CAW, WAM
Water hammer arrestors of the APW, CAW e WAM series are devices designed to absorb pressure surges, commonly known as “water hammer”.
They come in the following versions:
• Mini : 1/2" (for compact sizes APW, WAM)
• Standard : from 1/2" to 2"
Water hammer arrestors of the APW e CAW series offer a degree of protection in accordance with the specifications required by P.D.I (Plumbing and Drainage Institute – USA). Water hammer arrestors Series APW, CAW, WAM
Radiator Valves4-way thermostat adaptable valves for two-pipes and one-pipe heating systems Series 120B - 100M - 10
The 4-way thermostat adaptable valves, Series 120B, 102M, are used as shut-off and control devices for radiators in two-pipe and one-pipe heating systems respectively. The valves come in the configuration with 1/2” - 3/4” connection to the heat emitter and are provided with probe for separating the delivery flow from the return flow in the radiator. Connection of the valves to the heat emitter is through an O-ring sealed straight tailpiece and final washer with the aid of a hex. spanner. 120B-100M-102M Series
|Air separators and deaerators series ERD - SA - SAF|
The standard automatic air vent valves allow venting of air only when the latter is separated from the water and accumulated in the topmost zones of the system. The ERD deaerator allows reduction in speed with consequent aggregation of the air in maxi bubbles and the automatic venting of such air. Series ERD, SA, SAF
|Automatic air vents valves for solar energy systems Series MV-SOL|
MINIVENT valves Series MV-SOL are automatic air vent valves for solar systems. Valves are inspectionable, by unscrewing the cap from the valve tank (body). The seal between cap and valve tank is guaranteed from the presence of an O-ring, therefore it is possible to inspect and eventually clean the internal parts of the valve, in case of presence of foreign matters. Efficiency and functionality of the discharge mechanism during the time are guaranteed from the design characteristics of the valve. Sealing system is suitable to support vibration. Series MV-SOL
|Lockshield valves Series 195UM,196UM,1195UM,1196UM|
Lockshields Series 195UM, 196UM, 1195UM, 1196UM, are used as shut-off and control devices for heat emitters (radiators, fan coil convectors, radiant panels, etc.) in heating and air-conditioning systems. The lockshields are available in the configuration with straight or angle body, with male or female thread and should be installed on the return pipe of the heat emitter. They are fitted with an O-RING sealed straight tailpiece. Serie 195UM,196UM,1195UM,1196UM
|Thermostatic actuator with remote probe Series 148SD2|
The thermostatic actuator with remote copper probe, series 148SD2,is a device serving for controlling the flow rate of the heat-carrier fluid in relation to the operating temperature of the system. 148SD2
|Thermostatic actuators Series 148 - 148SD - 148CD - 148GA|
Thermostatic actuators Series 148, 148SD, 148CD are devices for automatic room temperature control, by acting directly on the radiator of radiator-type heating systems. The actuators, which are installed on the thermostat adaptable radiator valves, automate the valve plug movement through the presence of an element, inside the knob, which is sensitive to variations in room temperature.
CEN Thermostatic valve configurator
Series 148 - 148SD - 148CD - 148GA
|Thermostatic valve bodies with presetting series 130UM - 131UM - 1130UM - 1131UM|
Thermostatic valve bodies Series 130UM, 131UM, 1130UM, 1131UM are used as shut-off and control devices for heat emitters (radiators, fan-coils, radiant panels, etc.) in heating and air-conditioning systems, coupled with thermostatic actuators Series 138 and its derived products Series 148. The valves are supplied in the angle and straight body configuration, with male and female thread. They require installation on the radiator. Connection is through an O-ring sealed straight tailpiece using an Allen wrench. Characteristic of the O-ring is that it ensures perfect external sealing each time the valves are installed on radiators instead of others (manual) which involve the risk of the internal threading on the radiator plug no longer conforming.
CEN Thermostatic valve configurator
|Thermostatic valves Series 178UM - 179UM - 1178UM - 1179UM - 188UM - 189UM - 1188UM - 1189UM|
Thermostatic valves with simple setting series 178UM-179UM-1178UM-1179UM and those with pre-setting series 188UM-189UM-1188UM-1189UM are used as shut-off and control devices for heat emitters (radiators, fan coils, radiant panels, etc.) in heating and air-conditioning systems. The valves are available in the configuration with straight or angle body, with male or female thread, and should be installed on the delivery pipe of the heat emitter. Connection to the heat emitter is through an O-RING sealed straight tailpiece with use of a socket head wrench.
CEN Thermostatic valve configurator
Series 178UM - 179UM - 1178UM - 1179UM - 188UM - 189UM - 1188UM - 1189UM
Manifolds & FittingsCopper pipe fittings series 872M - 873M - 820R - 197
The Rafit+ fittings 872M Series are patented one-piece soft-seal fittings, for connecting copper piping and hydraulic components of the system (valves, lockshields, manifold side outlets, etc.). The 872M Series fittings are made of a set of parts assembled in an automatic process, namely:
• Tightening body
• Vulcanized EPDM seal on steel insert
• Cutting ring
• Lock ring nut
The characteristic feature of the one-piece fittings, is that of allowing quicker connection operations as compared to the conventional unions (three-piece fittings). The 872M Series fittings use PIPE thread in accordance with UNI ISO 228 standard. The fittings stand out for their stylish design, differing from the hexagonal standard one of normal fittings, therefore they are especially suitable for installations in residential buildings. Copper pipe fittings series 872M - 873M - 820R - 197
|Preassembled manifolds with flow meter Series CPRFLW|
The preassembled manifolds of the CPRFLW series allow building up systems for distributing the heat carrier fluid to heating and air conditioning installations (above all for heating systems with radiant floor heating panels).
The manifolds are available with NTP threading and in the following versions :
• Head connections 1 1/4" MF
• Side outlet connections 3/4" M
• Centre distance between the outlet connections 50 mm
The manifolds, supplied already preassembled on brackets, are provided with :
• Delivery manifolds complete with flow meters series FLMR
• Return manifolds series 822MM
• Two ball shut-off valves series 210
• Two end-pieces for manifolds series 823MP complete with drain cocks series 238, air vent valves series MVD and immersion thermometers series T Series CPRFLW
|Single brass manifolds for radiant panel heating systems Series 822MM - 822MR - 822MME - 822MRE|
The Modul manifolds of the 822MM, 822MR, 822MME, 822MRE series allow building up systems for distributing the heat carrier fluid to heating and air conditioning installations (above all for radiant panel heating systems).
The manifolds are available with NTP threading and in the following versions :
• Head connections 1"MF, 1 1/4"MF
• Side outlet connections 1/2"M, 3/4"M, 3/4"M EUROCONUS.
The manifolds are provided with :
• Prefitted O-ring to allow easy assembly of the manifolds by ensuring water tightness without resorting to conventional means (sealing with hemp).
• Locking nut which also allows correct alignment between the side outlet connections.
• Control devices in series 822MM, and shut-offs in series 822MR hence reducing space required for installation and allowing control of each single circuit. series 822MM - 822MR - 822MME - 822MRE
|Single manifolds Series 805M - 806M - 807M - E807M|
The Modul manifolds of the 805M, 805ME, 806M, 807M, E807M, E810M series allow building up systems for cold and hot water distribution in heating, air-conditioning and plumbing systems.
The manifolds are of brass construction, complying with the following standard:
• UNI 5035/62
They are available with BSP (GAS) threading in the following versions with:
- Head connections 3/4", 1", 1.1/4"
- Side outlet connections 1/2"M, 3/4"M and 3/4"M EUROCONO.
• Above all the manifolds of the 805M and 805ME Series are provided with:
- A prefitted O-ring to allow easy assembly of the manifolds by ensuring water-tightness without resorting to conventional means (sealing with hemp);
- Locking nut which also allows correct alignment between the side outlet connections. Series 805M - 806M - 807M - E807M
System Products2-way, 3-way zone valves Series VU02 - VU3 - VU4
The Series VU zone valves are normally used for controlling hot and cold water flows in heating and/or air conditioning systems through an electrical ON/OFF or modulating control. The valves, made of brass, are offered in the configuration with female connection ND 3/4" and 1”, in the following versions :
- 2-way Series VU02
- 3-way Series VU3
- 3-way and 4 connections if the VU3 valve is used with by-pass Series VU4
The valves can be operated by the following electrothermic actuators :
• with On/ff action, Series ETE
• with modulating action, Series ETM VU02,VU03,VU4 series
|AQUAMIX-Thermostatic mixing valve for radiant panel heating systems series 63C|
The Aquamix thermostatic mixing valve, Series 63C, is offered with female threaded connections and 10 setting positions. The valve body is made of brass, chrome-plated, inside and out. The valve has a teflon coating inside which considerably reduces the amount of scaling caused by hard water. Each valve is provided with two mesh strainers which, when fitted to the hot water (+) and cold water (-) ports avoid debris entering the valve thereby protecting valve operation. Series 63C
|AQUAMIX-Thermostatic mixing valves series 61C - 62C|
The thermostatic mixing valves Aquamix Series 61C, 62C and 61CM are offered in versions with male and female connections as well as 4 setting positions. The valve body is made of brass nichel-plated on both inside and outside; moreover an inner teflon coating is provided in order to reduce scaling caused by hard water. Each valve is provided with two mesh strainers which, when inserted inside the hot water (+) and cold water (-) ports avoid depositing of coarse particles thereby protecting valve operation. Series AQUAMIX
|By-pass valves Series 466 Thermatic and Series USVR|
By-pass valves series 466 Thermatic and series USVR are devices for differential pressure control between two points of a circuit, designed in order to overcome the problems of variable flow rate plants and guarantee the by-pass which is proportional to the difference between the nominal pump head and the working conditions. Series 466-USVR
|Electro-Mechanical Modulating Actuator Series EMUJC|
The Series EMUJC actuator is a modulating electromechanical actuator supplied with 24V by means of a three-point control or 0-10V (0-5V and 5-10V) control signal. Its distinguishing features are its compact size, which enables it to be installed in small spaces (fan coils, etc...) and its ease of assembly in that no hydraulic operations (system drainage) are required to couple the servo controls with the valve bodies. It also has a LED that signals its operating status. series EMUJC
|Electronic pump control unit Series WACOPUMP2|
The electronic unit of the WACOPUMP2 series controls start and stop of the pump when any tap or valve of the system is opened or closed. When the pump is started, it remains running as long as there is demand by the user thus supplying the water main at constant flow rate and pressure rate. Series WACOPUMP
|Fan Coil valves Series 2131 - 3131 - 4131|
Fan-coil control valves series 2131, 3131, 4131 are used for controlling the flow of hot or cold water in heating and air conditioning systems. They are operated by electric actuators with max. stroke of 2.5 mm. such as electrothermic actuator series 22C. As standard, the valves are available in the configuration with male thread in the following versions :
• 2-way series 2131
• 3-way series 3131
• 3-way with 4 ports series 4131 with built-in by-pass.
Operation of the valve plug is by electrothermic actuator series 22C, available in the following versions:
• NO (normally open) 2-wire(Standard) or 4-wire (with auxiliary microswitch contact)
• NC (normally closed) 2-wire (Standard) or 4-wire (with auxiliary microswitch contact)
All actuators of the 22C series can easily be fastened to the valve body with a threaded ring nut. (M30x1.5). Series 2131 - 3131 - 4131
|ON/OFF Electrothermic actuators Series 22C|
The electrothermic actuators 22C series are ON/OFF devices used for automatic actuation of the valves on:
- thermostatic adaptable valves series 178UM, 1178UM, 179UM, 1179UM, 188UM, 1188UM, 189UM, 1189UM, 130UM, 131UM, 102M, 100M, 120B.
- reverse body valves series 180M
- fan coil valves series 2131, 3131, 4131
- manifolds series 822M
The electrothermic actuators are available in the following versions:
• NA (normally open)
• NC (normally closed)
• 2-wire (Standard) or 4-wire (with auxiliary contact).
Both easy to fix on the valve body with a threaded ring nut. The electrothermic actuators are designed to run on 24V and 230V. Series 22C
|Preassembled fixed-point control distribution unit for radiant panel heating systems DOMORADIANT|
The preassembled unit of the DOMORADIANT Series is designed for modern radiant panel heating systems.
It performs all the necessary functions for such purpose, namely:
- providing tight-sealed hydraulic connection of the pipe ends in the various coils making up the radiant panels
(CPRFL series); it allows shut-off (if required) and the necessary setting and monitoring of all flow rates
- providing the hydraulic connection for the pipes feeding the towel-rail radiators (807MF series)
- automatic air venting
- mixing of the fluid for the radiant panels and holding it at low temperature
- ensuring the supply and head of the high temperature circuits
- visual temperature monitoring.
The device designed for mixing and delivering hot water at the lower temperature consists of a 3-way mixing valve operated by a thermostatic actuator with remote sensor type FH-148SD (range 20-50 °C). The required flow rate for feeding the radiant panels is supplied by a 3-speed electrically driven pump. The manifold can supply up to 12 low temperature circuits and up to 3 radiators. Each return outlet is arranged to receive thermostatic actuator series 22C for adjusting the ambient temperature in each individual room. The supply outlet is fitted with flow meter FLMR series able to measure and adjust the flow rate accordingly. Optionally the various electrothermic actuators (when provided) can be controlled by a modular control box WFHT series, from 4 to 6 zones through room thermostats. The Master module is provided with a control relay for the electrically-driven pump which is automatically disactivated when all the actuators are closed. When the actuators are not controlled by the modular box, a by-pass kit is available for controlling the differential pressure. Such kit should be attached to the head connections of the manifolds. The system, which has been hydraulically tested in the factory, is housed in a special inspection box with single door and with epoxy finishing. DOMORADIANT
|Remote thermal units for centralized combustion systems Series DOMOCAL|
The multi-function DOMOCAL thermal units are designed to control the heat supply, coming from a district heating station or produced by a conventional heating system, to the individual apartments, whether for space heating or preparation of Domestic Hot Water (DHW). DOMOCAL feeds the heating circuit of each apartment and allows independent control of the room comfort level thanks to the action of a timing thermostat installed in the ambient, that actuates the zone valve incorporated in the unit. Supply of the DHW produced by the heat exchanger is made available merely by turning the tap for hot water delivery. Temperature of the hot water is controlled by a thermostatic mixing valve which holds it at the level chosen by the user. The devices and pipes making up the unit are factory-assembled and are inserted in a metal support structure which allows pendant installation. All inlets and outlets are provided with shut-off valves and union fitting (three-piece): during installation, this allows preparing just the frame at first, then inserting the "body" of the unit at a later stage. Likewise it is easier for the heating system operator to carry out the required maintenance work and also full replacement of the unit when necessary. The DOMOCAL thermal unit is equipped with a direct heat (hot/chilled) metering system, approved by the PTB Institute of Berlin, which allows subsequent allocation of the costs based on consumption, thus encouraging a more rational use of energy with consequent energy instant savings. The thermal energy drawn from the primary network (user consumption) is measured with great accuracy by a meter whose data/consumption reading is concentrated, transmitted and processed. The system is also provided with a meter for the drawing off cold mains water. DOMOCAL series
|Silane cross-linked polyethylene INTERSOL®PEX-b|
Piping of the INTERSOL®PEX-b series is made from cross-linked polyethylene, available in versions with or without oxygen diffusion barrier, and suitable for pipes used for supplying the heat carrier fluid in heating/plumbing systems. Silane cross-linked polyethylene INTERSOL®PEX-b
|Thermal safety drain and draught regulator Series STS - RT|
- Thermal safety drain Series STS : The heat sensitive element, immersed in the boiler water, expands as temperature increases thus causing the valve plug to open when the temperature reaches the set value.
- Draught regulator Series RT: The draught regulator heat sensitive element, immersed in the boiler water within a sheath, acts on the combustion by appropriately varying introduction of the combustion-supporting air in the boiler in relation to the water temperature. Such regulation is by opening or closing the air inlet door in the boiler. Series STS - RT